Chameth.com - posts like break-everything-fuzz-testing, g15-ram-upgrade, travel-toolkit but not finding-an-awkward-bug-with-claude-code, why-you-should-be-using-https

Building a travel toolkit

2025-01-02T00:00:00Z

The container for my toolkit, a UGREEN “travel accessories” bag

For a while now, whenever I’ve traveled anywhere I’ve dumped a selection of tools into my backpack just in case I need them. Originally this was mostly focused around being able to open and fix my laptop if anything went wrong, but over time has slowly expanded to include other useful tools.

Repeatedly packing these tools and then returning them to where they belonged was tedious, though. I couldn’t just leave them in the backpack as I often needed them for non-travelling purposes, and I didn’t want to just buy duplicate tools that spent most of their life a few meters away from each other, so I ignored the problem and just dealt with the tedium.

Eventually I acquired enough tools that — while not quite duplicates — I wouldn’t miss often if they were kept in the backpack. Building on these I’ve created a little travel toolkit that contains everything I might want (and more) while away.

The base

The biggest challenge I had before was finding a screwdriver set. I have an iFixit Mako set that did the in-and-out-of-the-bag routine for several years. Nothing else covered the range of drivers I wanted for generic electronic tinkering and more chunky work. I finally found one in the form of a Wera Tool-Check PLUS TR-Edition. “TR” stands for “Tool Rebel” and is Wera’s “fan club” brand. Its signature features over the normal Tool-Check PLUS are a fancy fabric case and a 152mm bit extender; but it also comes with a much different set of bits, which is why I picked it up.

Here’s a comparison

Type	Standard version	Tool Rebel edition
Phillips	2x PH1 3x PH2 1x PH3	1x PH00 1x PH0 1x PH1 1x PH2 1x PH3
Pozidrive	None	1x PZ1 3x PZ2
Slotted	1x 5.5mm	1x 4mm 1x 4.5mm 2x 5.5mm 1x 6.5mm
Torx	1x T10 1x T15 1x T20 1x T25 1x T30 1x T40	1x T10 1x T15 1x T20 1x T25 1x T30 1x T40
Security Torx	1x T10 1x T15 1x T20 1x T25 1x T30	1x T25
Hex	1x H3 1x H4 1x H5 1x H6 1x H8	1x H1.5 1x H2 1x H2.5 1x H3 1x H4 1x H6 1x H8

There are only five bits present in the standard version that are missing in the TR edition: 5mm hex (pretty uncommon) and four sizes of security torx (rare). In exchange for those and the removal of a bunch of duplicates, you get two extra phillips sizes (0 and 00, both very useful for electronics and spectacles), some pozidrive bits (extremely common on random hardware/furniture/etc), smaller hex bits (for electronics, 3D printers, and so on), and a few other bits and pieces.

Overall it’s a vastly superior selection for my needs. And while it doesn’t have the full range of bits provided by the iFixit kit, it does cover almost everything I’m ever actually likely to need while travelling, and it’s probably around a third of the size.

The other core part of the toolkit is the bag. I had a UGREEN “travel accessory” bag hanging around unused, and noticed it was almost the exact right size for the Tool-Check. Now, how many other tools could I stuff in there?

All the tools

The array of tools that make up the travel toolkit

The kit can be broken down into a few sections:

Screwdriving

The aforementioned Wera Tool-Check
Its 152mm bit extender

I’ve talked enough about this already, I think, so I’ll spare you any additional commentary on screwdrivers and bits.

Splitting, gripping and cutting

Engineer tweezers
Engineer mini snips
Engineer mini screw removal pliers
Knipex mini waterpump pliers
Two iFixit spudgers (one metal, one plastic)
iFixit jimmy

I have bigger or slightly different versions of these that stay in my normal toolkit. The tweezers and snips are useful in a variety of situations, and the spudgers are handy for getting inside laptops and other devices. The pliers are less useful, but they’re one of those things where when you do need them there aren’t any good alternatives.

Sewing

Two needles
Some black thread
Set of mini clips

You never know when you’re going to rip a seam in something. I find the clips a lot less fiddly than using pins for keeping material in place when I’m trying to sew.

Computering

Retractable ethernet cable
RJ45 coupler
USB-C to RJ45 adapter
Dual USB-A and USB-C thumb drive, with an Arch ISO on it

Sometimes Wi-Fi just doesn’t cut it, or you need to fiddle with a router that doesn’t expose its admin UI over Wi-Fi. The USB-C adapter is for use with my phone, as it’s often easier to move that get the laptop where it needs to be.

I can boot from the thumb drive into an Arch environment, and from there reinstall my laptop from scratch if needed. There’s enough space left over so it can be used to transfer files as well.

Miscellaneousing

Fabric tape measure
Spirit level
Sharpie
Superglue
Spare batteries: 2 CR2032s, 2 AA, 2 AAA

I’m almost certain I won’t use the spirit level, but it’s tiny and I had a spare so it went in. Everything else is just in the “generally handy to have” category.

Putting it all together

The nicely-organised side of the toolkit

The Tool-Check PLUS fits almost perfectly into one side of the UGREEN bag, leaving a little wiggle room along the side for the longer parts like spudgers. The middle pockets can’t fit much in, but keep the batteries and sewing bits out of the way. Everything else is in a big zip-up compartment in the other side, which is slightly messy but still easy enough to dig through to find whatever I need.

The complete kit weighs in at around 1.2KG, so it’s not exactly lightweight, but it goes in a bag with a heavy laptop and all of its peripherals so it’s not as noticeable as it might otherwise be.

It remains to be seen how much use I’ll actually get out of any of this. Maybe I’ll put a bit of paper in so that I can track how often I use each tool…

Upgrading the RAM in a Dell G15 laptop

2023-07-29T00:00:00Z

The Dell G15

I currently use a Dell G15 laptop for work. It has served me well for a little over a year, but recently it has been struggling a little with my day-to-day workload. It came with 32GB of RAM — the highest possible specification at the time¹ — but that is apparently no longer enough for me.

For a recent project, I was working on a Rust library used in an Android app. That meant running the usual glut of Android tools (Android Studio, an emulator and at least one Gradle daemon) alongside a normal IDE (IntelliJ IDEA). Throw in a web browser and a couple of electron apps, and I often managed to use all 32GB.

When you start swapping memory out to an encrypted disk — even an SSD — it doesn’t make for great performance. At first, I tried to work around this by enabling the Linux out-of-memory (OOM) killer, but it turns out that it’s not too good with Electron apps: it will kill the large browser process, but then the small Electron wrapper will just respawn it.

Can it be upgraded or not?

The obvious solution to not having enough RAM is to add more RAM. A quick look in the manual showed this might not be possible, though. The manual includes the following “Memory specifications” table:

Description	Values
Memory slots	Two SODIMM slots
Memory type	DDR5
Memory speed	4800
Maximum memory configuration	32GB
Minimum memory configuration	8GB
Memory size per slot	8GB or 16GB
Memory configurations supported	8 GB, 1 x 8 GB, DDR5, 4800 MHz 16 GB, 1 x 16 GB, DDR5, 4800 MHz 16 GB, 2 x 8 GB, DDR5, 4800 MHz, dual-channel 32 GB, 2 x 16 GB, DDR5, 4800 MHz, dual-channel

That unambiguously says that an upgrade from 32GB is not possible. I gave up.

Later though, I was complaining about memory issues to a friend, and he pointed out a Dell forum thread where a couple of people claim to have successfully installed dual-channel 32GB modules. Since the alternative was getting an entire new PC after only a year, I decided to give it a go.

The upgrade attempt

I ordered a pair of Crucial 32GB DDR5-4800 SODIMMs, and after they turned up dismantled the laptop. The G15 comes apart pretty normally: there are uncovered screws on the bottom holding the lower part of the case on. With those removed and some gentle prying, it pops off, and you get access to the battery, GPU and motherboard.

The first thing I saw was this:

The G15 motherboard adamantly proclaiming that it doesn’t want 32GB SODIMMs

Not one but two labels that indicate it will only accept 8GB or 16GB modules. Oh well, what’s the worst that can happen?

Oops?

I dutifully installed the new modules, reconnected the battery and put the case back together. I pressed the power button, and… nothing. None of the usual garish lights that immediately come on, no screen output, just a dead laptop. After reading some more of the user manual, I found that there is a tiny status LED on the side next to the ethernet port. Forcing the laptop to power off and back on again, the status LED blinked a distress code at me: 2 amber blinks, 4 white blinks. The manual says that is — unsurprisingly — a memory fault.

I figured at this point that the manual and labels on the motherboard were probably right. I took the laptop apart again, reinstalled the original 2x16GB modules, reassembled it, and pressed the power button. It didn’t boot. I don’t spend a lot of time fiddling inside computers, but I’ve done it enough that I’m reasonably confident I can’t entirely break a computer while swapping some RAM modules. I took to Googling², and found an interesting article that said Dell laptops don’t like to boot after RAM changes unless you clear the CMOS by popping out the battery for 15 minutes.

I opened the laptop up, and looked around for the CMOS battery. There wasn’t one. Turns out they don’t exist any more. I left the main battery disconnected for a while to see if it would help, and it didn’t.

Unexpected success

I started to get worried: if I couldn’t fix this, I wouldn’t be able to work until I got a new PC, and that wasn’t really in my budget at the minute. I sat reading old forum threads and help guides³, none of which were actually useful. Out of nowhere, though, the laptop booted up.

Naturally, I immediately shut the laptop down again, opened it up, and switched back to the new RAM modules. Then I turned it on again and sat waiting. After about 15 minutes of it looking totally dead, it turned on and showed a BIOS warning about the hardware configuration being changed. It then booted perfectly normally, and all 64GB of RAM was visible and usable.

My theory is that the forum threads were right: Dell laptops are funny about RAM upgrades. But somehow in removing the physical CMOS battery, they’ve kept the same “you have to wait 15 minutes” behaviour just without any indication that’s what’s happening. Regardless, I now have enough RAM even for the greediest of IDEs and Electron apps.

Bizarrely, the maximum spec has decreased to 16GB since then. ↩︎
In the generic sense. I use Kagi these days. ↩︎
On my phone because, y’know, the laptop was busted. ↩︎

How to break everything by fuzz testing

2020-04-26T00:00:00Z

Fuzz testing is a bit like the infinite monkey theorem, but instead of Shakespeare you get crashes.

Fuzz testing, if you’re not aware, is a form of testing that uses procedurally generated random inputs to see how a program behaves. For instance, if you were fuzz testing a web page renderer you might generate a bunch of HTML - some valid, and some not - and make sure the rendering process didn’t unexpectedly crash.

Fuzz testing doesn’t readily lend itself to all types of software, but it particularly shines in cases where some kind of complex user input is accepted and processed in some way - like the aforementioned web page renderer. I was recently adding a library to parse EXIF data to images to an Internet-facing service and realised it was a perfect opportunity to do some fuzz testing. Even if I didn’t find any issues, I’d improve my confidence that the library was safe enough to expose to the Internet.

Breaking my EXIF library

I wrote a quick harness to run go-fuzz on the library, and gave it some pre-existing demo files as sample input. The way go-fuzz works is that it instruments your code and then mutates the inputs to try to improve the coverage. For example, if I had some sample data that had an EXIF tag with a value of 1 then go-fuzz might change it to a 2 and see if the code follows a different path. In most cases it won’t but when it does, they tend to be very interesting cases.

One of the first issues that go-fuzz found was that some values in a maker note field would cause the library to panic (i.e., crash). This happened because there was a check to see if the first six characters were “Nikon” and a null byte, without first checking to see if there were actually six characters available. This is a kind of bug that doesn’t happen much with “real” data - as the field is either not present or completed correctly - but could easily be exploited once this code is exposed to the Internet.

Another interesting bug that go-fuzz found was that if a tag had a particularly large count, the library would try to allocate an obscene amount of memory and die. There was already a check in the code that was meant to avoid this exact scenario, but go-fuzz managed to find a way around it. Each tag has a size (for example an integer tag takes a fixed number of bytes) and a count; the existing check multiplied the two together and made sure that the result wasn’t too large. For most cases this was fine but go-fuzz found a case where the count was so large that when multiplied by the size of the tag it overflowed the integer and became negative, thus passing the sanity check but then subsequently failing when it came around to actually allocating the memory.

The final bug of note that go-fuzz found was the most interesting. EXIF data is stored in IFDs (“Image File Directories”), and each IFD provides what is effectively a pointer (a byte offset) to the next one. The EXIF library already had a check to make sure that these didn’t loop, but it only checked the immediately preceding IFD - so if IFD 1 linked to IFD 2, it would catch IFD 2 linking back to IFD 1 and break the loop with an error. Go-fuzz found that having three interlinked IFDs had the same issue, though, and the guard code wasn’t triggered. This created an infinite loop, maxing out a CPU core until the process was eventually killed - one of the worst kind of bugs you could have in an Internet-facing service which doesn’t deal with private data! The fix for this was fairly straightforward - I just made the library keep a record of the previously visited IFDs and bail out if it found a loop.

Breaking my IDE

When go-fuzz detects an issue it outputs not only the details of the problem (the stack trace, error message, and so forth) but also the input that generated the problem. This is useful for reproducing and making sure the issue is fixed, but it also makes it really easy to write a test to ensure that the behaviour never regresses in the future.

As I was working through fixing the bugs that go-fuzz found, I dutifully added new tests where needed. After adding the sample input with looping IFDs to the project, I switched to IDEA to write a test to use it. I clicked on the input file to copy the file name, and then the entire IDE hung and had to be restarted. Uh oh! When I restarted IDEA, it immediately began indexing the project and again hung. It turns out IDEA parses EXIF data (presumably, even if it does nothing else with the data, to get the rotation property for images), and the library they use - an independent one written on Java - had the same bug as the Go library I was using.

In order to stop IDEA from indexing the file and becoming unusable I renamed it from a ‘.tif’ extension to ‘.dat’, and everything went back to normal. I thought I’d best report the bug to JetBrains, though, so they could put a proper fix in.

Breaking YouTrack

JetBrains use their own issue tracker called YouTrack for reporting bugs in IDEA. I dutifully went over and described the problem, attaching the log files from the IDE, a description of how the file was malformed, and carefully selected the .dat version of the file to upload so that it wouldn’t cause anyone else the same immediate problem.

After trying to upload the file I got a strange error back. Uh oh! I submitted the IDEA issue as it stood, unable to see if the attachments had even uploaded, and went and wrote up an issue for YouTrack itself about the error message. While I was doing that, YouTrack seemed to slow down and become really annoying to use. I had a sinking feeling the exact same thing was probably happening as with IDEA and my library - but this time YouTrack had content-sniffed the file instead of relying on the file extension. In hindsight, I should’ve put the file in a passworded archive to ensure no automated tools got hold of it. I marked the issue as a security problem as in a service like YouTrack it presents a denial-of-service opportunity¹ (remember when I said it was one of the worst kinds of bugs you could have in an Internet-facing service?…)

Shortly after I raised my YouTrack ticket, a notice appeared at the top of the page saying they were investigating the current performance issues. Uh oh! I was holding out hope that this was unrelated to me uploading the buggy dat file, but the timing all seemed a bit suspect. I shot support an e-mail saying I think I might be the root cause for their performance issues and linked to the ticket. In the time it took me to e-mail them, the entire site had been put into maintenance mode. I got an e-mail back a few hours later confirming the outage was in fact all my fault, as I’d feared. Within the space of days the JetBrains security team had fixed the issue in YouTrack, which was a pretty nice turnaround.

So if you were trying to access YouTrack at the start of March and couldn’t - I’m sorry, I didn’t mean to! Also, if you’re building an Internet-facing service that takes user input you should really consider running a fuzz tester against it!

“We have a problem”. “Remember, there are no such things as problems, only opportunities”. “Well then we have a DDoS opportunity.” – @J4vv4d ↩︎